Daily maintenance of CO2 laser cutting machine

    CO2 laser cutting machine is an important laser cutting machine.Its daily maintenance is also very important.What are the main maintenance methods?

    1. Replace the water and clean the water tank (it is recommended to clean the water tank and replace the circulating water once a week)

    Note: Make sure the laser tube is filled with circulating water before the machine works.

    The quality and temperature of the circulating water directly affect the service life of the laser tube.It is recommended to use pure water, the temperature of which should be controlled below 35℃.When the temperature exceeds 35℃, the circulating water should be replaced or ice should be added to the water to reduce the water temperature.It is recommended that users choose one cooler or use two tanks.

    Clean the water tank: First, turn off the power, pull out the water inlet pipe, let the water in the laser tube flow into the tank automatically, open the tank, take out the water pump, and remove the dirt from the pump.Clean the water tank, replace the circulating water, return the water pump to the tank, insert the water pipe connecting the water pump into the inlet, and arrange the connector.Start the pump separately and run for 2-3 minutes (make the laser tube full of circulating water).

    2. Fan cleaning

    Long-term use of the fan will make the fan accumulate a lot of solid dust, make the fan produce a lot of noise, is not conducive to smoke and deodorization.When the suction of the fan is insufficient and the exhaust pipe is not smooth, first turn off the power, remove the air inlet and exhaust pipe on the fan, remove the internal dust, then reverse the fan, pull the internal blade clean, and then install the fan.

    3. Lens cleaning (it is recommended to clean the lens before work every day, and the equipment must be turned off)

    In the previous introduction to the machine, it was mentioned that the engraving machine has three mirrors and a focusing mirror (the first mirror is located at the laser tube transmitter, i.e. the upper left corner of the machine, the second mirror is located at the left end of the beam, the third mirror is located at the top of the fixed part of the laser head, and the focusing mirror is located in the adjustable tube under the laser head).The laser is reflected and focused by these mirrors, and then emitted from the laser.The lens is prone to dust or other pollutants, resulting in laser loss or lens damage.No. 1 and No. 2 lenses do not need to be removed during cleaning. Just wipe the lens paper carefully and dip the cleaning solution into the center of the lens to the edge of the lens.The No. 3 lens and the focus lens need to be removed from the frame, wiped in the same way, and then installed after the wipe.

    Note: 1 the lens should be gently wiped without damaging the surface coating;2. The lenses should be treated gently to prevent falling off during wiping;When installing the focusing lens, keep the concave surface downward.

    4. Cleaning of guide rail (it is recommended to clean it once every half a month and turn off the machine)

    As one of the core parts of the equipment, guide and straight spool play a guiding and supporting role.In order to ensure the high machining precision of the machine tool, the guide rail and the straight line are required to have high guiding precision and good motion stability.During the operation of the equipment, a lot of corrosive dust and soot will be produced during the processing.A large amount of dust accumulates on the surface of guide rail and straight bobbin for a long time, which has a great influence on the machining accuracy of the equipment. Corrosion points will form on the surface of guide rail bobbin, shortening the service life of the equipment.In order to ensure the normal and stable operation of the machine and the processing quality of the product, the daily maintenance of guide rail and straight spool must be done.

    Daily maintenance of CO2 laser cutter is very important, it will directly affect the efficiency improvement.

---

    CO2 laser engraving machine for leather

    In our daily life, from leather clothes, leather bags, leather pants, leather shoes, watch belts, handicrafts, cars, ships, planes and other leather products, we can see a variety of leather products, in these leather products, we can see some beautiful patterns and words.Do you know how these patterns and words appear on leather goods?

    Many people would think these were printed using traditional techniques.Sure, traditional technology can print beautiful pictures and text on leather, but you probably didn't know there was a device that could do better, and that was the CO2 Laser engraving machine. So what are the advantages of the CO2 laser engraving machine?

    When will CO2 laser engraving machine be used for leather processing? It will not cause any damage to the leather. The engraving speed is fast and accurate, and there is no graphics or text.Laser processing belongs to thermal processing.It USES a high-energy laser beam to instantly burn and sculpt the leather surface, with little thermal effect.Therefore, although high quality laser beams do not damage the leather.In addition to marking text, you can also mark national languages, symbols, 2d codes, and barcodes.

    Any CO2 laser engraver with a pattern is timeless and the marked pattern is exquisite and beautiful.In addition, CO2 laser engraving machine can help enterprises save costs.In the process of processing, CO2 laser engraving machine will not have any consumables, no secondary processing, can save a lot of labor costs and unnecessary consumables costs.The equipment also needs 20,000 small pieces, the equipment also has a 24-hour continuous performance, can meet the needs of large-scale production line processing.