1) advertising engraving machine single or three axis does not walk or walk abnormal

 

1. Loose or malfunctioning control card
2. Drive failure of the corresponding shaft
3. Failure of the corresponding axial stepper motor
4. The corresponding connecting device is broken or loose (the symptoms of the connecting device are loose, and the font is misplaced during carving)
5. The corresponding screw is broken or the screw nut fails
6. Failure occurs in the sliding speed of the corresponding shaft
7. Driver fine fraction, current, and software Settings are not the same.

 

2) the engraving machine engrave in different shades

 

1. Loose or malfunctioning control card
2. Failure of stepper motor
3. Drive failure or current subdivision is inconsistent with software Settings
4. Z axis motor line fault;5. Spindle motor failure
6. Frequency converter interference or wrong data setting
7. Static interference
8. Computer virus or system problem
9. Uneven working platform.

 

3) there is an error in the advertising engraving machine

 

1. Loose or malfunctioning control card
2. Drive failure
3. Failure of stepper motor
4. Static interference
5. Motor line fault
6. Data line failure
7. Wrong path
8. Broken or loose coupling
9. The processing speed is too fast;(system parameters curve acceleration over large)
10. Computer system problem or virus.

 

4) advertisement carving machine z-axis out of control (stab knife)

 

1. Loose or malfunctioning control card
2. Static interference
3. Z axis motor line fault
4. Wrong file path
5. Frequency converter interference
6. There is something wrong with the computer system or a virus
7. Insufficient power of z-axis motor, loose coupling
8. The current of z-axis driver is too low, or the signal line is connected incorrectly.

 

5) advertising engraving machine random engraving

 

1. Control card failure
2. Frequency converter interference
3. Wrong file path
4. Static interference
5. There are problems with the software setup
6. Drive failure or wrong setting of current subdivision
7. Data line failure;The computer has a virus or system problem.

 

6) engraving machine milling bottom uneven

 

1. The spindle is not perpendicular to the table surface and should be corrected (symptoms: the depth of the knife is different from that of the knife)
2. The knife has problems
3. There is something wrong with the control card
4. There is a problem with the Z drive or Z lead screw.

 

7) when the engraving machine appears misalignment or wrong size

 

1. Check whether the path of carving software is correct or not
2. Check the clearance size of the screw rod and whether the fastening screw of the smooth rod is loose
3. Check that the software parameters are set correctly.

 

8) when the X-axis of the engraving machine walks a certain section, the z-axis does not lift the knife, but press up to go down

 

1. Check whether the z-axis stepper motor is in normal operation, the power and the driver current or its own fault
2. Check whether the line of the z-axis stepper motor has bad contact or is in the middle of disconnection
3. Control card failure.

 

9) the spindle motor of the engraving machine does not turn or reverse

 

1. Check the parameter setting of the frequency converter
2. Whether the signal line of the inverter is connected backwards.

 

10) when the engraving machine opens the software and starts up, the shaft appears to close

 

1. Drive problem or bad contact of computer output signal line
2. Motor wire contact is poor.

 

11) the limit phenomenon appears in the engraving process of the engraving machine

 

1. Check whether the carving path exceeds the carving range
2. Soft limit set by parameters in the software.

 

12) the engraving machine sending software can not be opened normally, the thing carved is deformed.

 

1. Re-install the new system and software
2. Check whether the screw of X and Y axis is loose;The carving knife has problems.

 

13) the spindle motor stops or slows down suddenly in the working process of the engraving machine

 

1. If the working voltage is unstable or overloaded, add a voltage stabilizer
2. Check whether the middle line is well connected and whether the thread head is out of welding.

 

14) when the engraving machine sets the origin, sometimes the offset distance to the right is uncertain

 

1. The limit switch fails. In the process of the system returning to the system origin, the limit switch has closed and bounced off
2. The drive line is loose, try to fix it tightly.

 

15) the position of X axis, Y axis and Z axis is variable when the engraving machine is started and reset

 

1. The limit switch is broken (the limit switch is always closed), it can be replaced
2. The drive wire is broken (short-circuit between 14 and 15 pins in X axis, 13 and 15 pins in Y axis, 31 and 15 pins in Z axis). Change the drive wire or open the short circuit
3. If the drive board is broken, replace it.

 

16) the spindle of the engraving machine stopped

 

1. Short circuit inside the spindle
2. Current shielding
3. Inverter parameter setting is wrong or its own fault
4. Control card failure
5. Short circuit of spindle or data line.

 

17) the rotation sound of the main shaft of the engraving machine is abnormal

 

1. Frequency converter setting is wrong
2. Spindle does not turn
3. There is something wrong with the spindle itself (bearing damage).

 

18) the direction of the engraving machine is opposite when walking or returning to the mechanical origin

 

1. Change files in notepad
2. Modify the connection method of inverter
3. Modify the motor direction in the weihong software.

 

19) the engraving machine cannot return to the mechanical origin normally

 

1. In the opposite direction
2. The control card is malfunctioning or loose
3. Fault of limit switch or data line
4. Drive failure
5. Stepping motor failure.

 

20) the main shaft of the engraving machine can't turn automatically or stop

 

1. Control card failure
2. Converter failure.

 

21) when the engraving machine opens the weihong software, the computer prompts "operation failed"

 

1. Check whether the driver of the board card is installed, or change the board card into a PCI slot
2. Reinstall the two data connection wires and check whether there is any broken needle
3. If there is a problem with the board card, replace it.

 

22) when the engraving machine opens the software, it will prompt: tri-axis alarm, initialization error no. 4

 

1. Check whether the two data cables of the computer and the machine are properly connected
2. Check whether the fuse of the adapter board in the control box is burned out and replace the fuse
3. Check whether the 85V power supply is normal.