In recent years, the fiber laser cutting machine has obvious advantages in cutting, and it has become a very important equipment in the current high-precision processing field. When cutting some metals or non-metals, the fiber laser cutting machine will be given priority, because the cutting material is Either bevel cutting or round tube cutting can meet the very high level of cutting requirements, and it can also be mass-produced, which greatly improves the working efficiency of the manufacturer and helps the manufacturer to obtain the largest profit margin.

   
   Moreover, the cutting quality of the fiber laser cutting machine is also guaranteed. Compared with other cutting machines, it can cut the product more neatly and smoothly. The production of the fiber laser cutting machine is absolutely absolute in terms of materials, work efficiency and environmental protection. Advantages, so it is a high-precision cutting machine that has developed rapidly in recent years. So what are the installation skills of more advanced fiber laser cutting machines? Let's take a look together.
 

 

 

 

1. Comply with the safe operation rules of fiber laser cutting machine. Start the laser strictly in accordance with the laser startup procedure.
 

2. The operator must be trained to be familiar with the structure and performance of the equipment, and to master the relevant knowledge of the operating system.
 

3. Wear labor protection equipment according to the regulations, and wear protective glasses that comply with the regulations near the laser beam.
 

4. Do not process a material before it is clear whether it can be irradiated or heated by laser, so as to avoid the potential danger of smoke and steam.
 

5. When the equipment is started, the operator shall not leave the post or be taken care of without authorization. If it is necessary to leave, the operator should stop the machine or cut off the power switch.
 

6. Keep the fire extinguisher within easy reach; turn off the laser or shutter when not processing; do not place paper, cloth or other flammable materials near the unprotected laser beam.
 

7. When an abnormality is found during processing, the machine should be shut down immediately, and the fault should be eliminated or reported to the supervisor in time.
 

8. Keep the laser, the bed and the surrounding area clean, orderly, and free of oil pollution. Workpieces, plates, and waste materials are stacked as required.
 

9. When using gas cylinders, avoid crushing the welding wires to avoid leakage accidents. The use and transportation of gas cylinders should comply with gas cylinder supervision regulations. It is forbidden to explode the gas cylinder in the sun or close to a heat source. When opening the bottle valve, the operator must stand on the side of the bottle mouth.
 

10. Observe high-voltage safety regulations during maintenance. Every 40 hours of operation or weekly maintenance, every 1,000 hours of operation or every six months of maintenance shall be carried out in accordance with regulations and procedures.

11. After the machine is turned on, the machine should be manually started in the X and Y directions at low speed, and check to confirm whether there is any abnormality.

12. After inputting the new part program, test run it first and check its operation.

 

1. The dual-focus laser cutting head is a vulnerable item on the laser cutting machine. Long-term use will cause damage to the laser cutting head.

 

2. Check the straightness of the fiber laser cutting machine track and the verticality of the machine every six months, and if it is found to be abnormal, it will be maintained and debugged in time. If this is not done, the cutting effect may not be so good, the error will increase, and the cutting quality will be affected. This is the top priority and must be done.

 

3. Use a vacuum cleaner to suck up the dust and dirt in the machine once a week, and all electrical cabinets should be closed tightly to prevent dust.

 

4. Frequently check the steel belt of the fiber laser cutting machine to ensure that it is tight. Otherwise, if there is a problem in operation, it may hurt people, or even cause death in serious cases. Don't underestimate some small accessories, a little carelessness may involve personal safety, so avoid safety hazards in all aspects.

 

5. The guide rails of the fiber laser cutting machine should be cleaned frequently to remove dust and other debris to ensure that the equipment is normal. The rack should be wiped frequently and lubricated to ensure lubrication without debris. The guide rail should be cleaned and lubricated frequently, and the motor should also be cleaned and lubricated frequently. The machine can move better and cut more accurately, and the quality of the cut products will be improved. .

 

The above is the correct use method of fiber laser cutting machine. There are more than hundreds of thousands of pieces of fiber laser cutting machine. So pay attention to it at all times during operation, and usually pay attention to maintenance and maintenance to increase the service life of the equipment, save costs, and increase benefit.